Product Title

Follow this installation procedure to install the Exo Terra Thermostat & Hygrostat on any size of Exo Terra Natural Terrarium:

1. Unlock the top screen cover and lift it off the terrarium.
2. Slide one of the inlet holes (located on the back of the screen top on either side) to the open position, so the wiring will fit through.
3. Feed the wire with sensor through the first available inlet hole on the preferred side on the back of the screen cover.
4. Position the sensor inside your terrarium, in the location where you want to reach the temperature & humidity setting. This can be on top of the substrate if you are using a Heat Mat or Heat Cable, but this can also be on a branch, cave or pile of stones if you are using a Ceramic Heater or Infrared bulb to heat up a certain basking area. NOTE: If using with a substrate heating device, please follow manufacturer’s instructions for safe use of the heating device.
5. Place the top screen cover back on the terrarium and lock it into position.
6. Close the remaining inlets by sliding the slider against the tubing or wires to prevent escape from feeding insects and smaller animals.
7. Place the Exo Terra® Thermostat & Hygrostat on a solid, level surface.
8. Connect your Heat Mat, Heat Cable or Ceramic Heater and a Fogger or Humidifier to the respective receptacle of the thermostat / Hygrostat. Controls heating devices up to 600W and humidifying devices up to 100W.

WARNING: Do not overload the Exo Terra® Thermostat & Hygrostat by connecting heat devices with outputs greater than 600W to the HEATING receptacle. Do not overload the Exo Terra® Thermostat & Hygrostat by connecting humidifying devices with outputs greater than 100W to the HUMIDITY receptacle. Damage from overloading is considered misuse and is exempt from the guarantee.

WARNING: Always read the complete instruction manual inside the product box.

Follow this installation procedure to install the Exo Terra Thermostat & Hygrostat on any size of Exo Terra Natural Terrarium:

1. Unlock the top screen cover and lift it off the terrarium.
2. Slide one of the inlet holes (located on the back of the screen top on either side) to the open position, so the wiring will fit through.
3. Feed the wire with sensor through the first available inlet hole on the preferred side on the back of the screen cover.
4. Position the sensor inside your terrarium, in the location where you want to reach the temperature & humidity setting. This can be on top of the substrate if you are using a Heat Mat or Heat Cable, but this can also be on a branch, cave or pile of stones if you are using a Ceramic Heater or Infrared bulb to heat up a certain basking area. NOTE: If using with a substrate heating device, please follow manufacturer’s instructions for safe use of the heating device.
5. Place the top screen cover back on the terrarium and lock it into position.
6. Close the remaining inlets by sliding the slider against the tubing or wires to prevent escape from feeding insects and smaller animals.
7. Place the Exo Terra® Thermostat & Hygrostat on a solid, level surface.
8. Connect your Heat Mat, Heat Cable or Ceramic Heater and a Fogger or Humidifier to the respective receptacle of the thermostat / Hygrostat. Controls heating devices up to 600W and humidifying devices up to 100W.

WARNING: Do not overload the Exo Terra® Thermostat & Hygrostat by connecting heat devices with outputs greater than 600W to the HEATING receptacle. Do not overload the Exo Terra® Thermostat & Hygrostat by connecting humidifying devices with outputs greater than 100W to the HUMIDITY receptacle. Damage from overloading is considered misuse and is exempt from the guarantee.

WARNING: Always read the complete instruction manual inside the product box.

Follow this installation procedure to install the Exo Terra Thermostat & Hygrostat on any size of Exo Terra Natural Terrarium:

1. Unlock the top screen cover and lift it off the terrarium.
2. Slide one of the inlet holes (located on the back of the screen top on either side) to the open position, so the wiring will fit through.
3. Feed the wire with sensor through the first available inlet hole on the preferred side on the back of the screen cover.
4. Position the sensor inside your terrarium, in the location where you want to reach the temperature & humidity setting. This can be on top of the substrate if you are using a Heat Mat or Heat Cable, but this can also be on a branch, cave or pile of stones if you are using a Ceramic Heater or Infrared bulb to heat up a certain basking area. NOTE: If using with a substrate heating device, please follow manufacturer’s instructions for safe use of the heating device.
5. Place the top screen cover back on the terrarium and lock it into position.
6. Close the remaining inlets by sliding the slider against the tubing or wires to prevent escape from feeding insects and smaller animals.
7. Place the Exo Terra® Thermostat & Hygrostat on a solid, level surface.
8. Connect your Heat Mat, Heat Cable or Ceramic Heater and a Fogger or Humidifier to the respective receptacle of the thermostat / Hygrostat. Controls heating devices up to 600W and humidifying devices up to 100W.

WARNING: Do not overload the Exo Terra® Thermostat & Hygrostat by connecting heat devices with outputs greater than 600W to the HEATING receptacle. Do not overload the Exo Terra® Thermostat & Hygrostat by connecting humidifying devices with outputs greater than 100W to the HUMIDITY receptacle. Damage from overloading is considered misuse and is exempt from the guarantee.

WARNING: Always read the complete instruction manual inside the product box.

When using the Exo Terra Thermostat & Hygrostat in combination with a visible-light emitting bulb (like Exo Terra’s Intense Basking Spot, Daylight Basking Spot or Daytime Heat Lamp) to create a daytime basking area or for ambient daytime heating purposes, you need to set the night-time temperature at its lowest point (10°C or 50°F) in order to avoid the bulb to emit light at night disturbing your animal’s normal activity cycle.

When using the Exo Terra Thermostat & Hygrostat in combination with a visible-light emitting bulb (like Exo Terra’s Intense Basking Spot, Daylight Basking Spot or Daytime Heat Lamp) to create a daytime basking area or for ambient daytime heating purposes, you need to set the night-time temperature at its lowest point (10°C or 50°F) in order to avoid the bulb to emit light at night disturbing your animal’s normal activity cycle.

When using the Exo Terra Thermostat & Hygrostat in combination with a visible-light emitting bulb (like Exo Terra’s Intense Basking Spot, Daylight Basking Spot or Daytime Heat Lamp) to create a daytime basking area or for ambient daytime heating purposes, you need to set the night-time temperature at its lowest point (10°C or 50°F) in order to avoid the bulb to emit light at night disturbing your animal’s normal activity cycle.