Reptile Dome Nano with Bracket
High Quality Fixture with Bracket
Reptile Dome Nano with Bracket
High Quality Fixture with Bracket
High Quality Fixture with Bracket
- Stylish and functional design, perfect for use with Nano & Mini terrariums
- Highly-polished aluminum dome increases light, heat and UVB output significantly!
- Easy to install and fully adjustable
- Ideal for use with Exo Terra’s NANO light bulbs (40W type A bulb)
- Heat resistant ceramic socket
- Self-adhesive support-bracket increases safety
- With On/Off switch and 6ft (180 cm) power cord
The adjustable bracket allows you to swivel the fixture from left to right to direct the heat and/or light sources to the preferred basking area in your terrarium. The fixture can be moved up or down to adjust the distance between the basking spot bulb and your animals in order to regulate the temperature of the basking area. The light can be easily turned on and off by the On/Off switch, mounted on the extra long power cord.
Stylish design, safety and ease of use were emphasised during the creation of this state-of-the-art fixture. Simply stick the self-adhesive support-bracket to the terrarium glass and the fixture is ready-for-use.
Ideal for use with Exo Terra’s Daylight Basking Spot NANO, Daylight LED Spot NANO or Infrared Basking Spot NANO.
Combine multiple fixtures to create a 24-hour cycle and/or to provide UV light to animals with UV-requirements.
Combine the Reptile Dome NANO Fixture with an Exo Terra Compact Top holding a Reptile UVB100, Reptile UVB150 or Reptile UVB200 depending on your animal’s UV requirements.
Pet care fixture for use with Reptiles, Amphibians and Invertebrates only!
Additional information
Item#: | PT2362 |
---|---|
Format: | 10 x 10 x 10.5 cm, 3,9" x 3,9" x 4,1" (WxDxH) |
UPC code: | 015561223621 |
FEATURES
A Red LED will indicate when the heating device is powered and once the set temperature is reached, the Red LED will no longer show.
A Blue LED will indicate when the humidifying device is powered and once the set humidity level is reached, the Blue LED will no longer show. The thermostat is accurate, reliable and easy-to-use!
Stylish and functional design, perfect for use with Nano & Mini terrariums
Highly-polished aluminum dome increases light, heat and UVB output significantly!
Easy to install and fully adjustable
Ideal for use with Exo Terra’s NANO light bulbs (40W type A bulb)
Self-adhesive support-bracket increases safety
With On/Off switch and 6ft (180 cm) power cord
diameter: 10cm / 4inch
Heat resistant ceramic socket
How to install
INSTALLING REPTILE DOME NANO
Glass surface preparation: surface temperature for application should be no lower than 60°F degrees (16°C) and not higher than 85°F degrees (29°C). If climate will not permit, move unit to appropriate conditions. Area to receive tape should first be thoroughly cleaned with a liquid detergent and warm water solution. Rinse with clean water and dry completely. A final wipe with 50/50 alcohol/water is highly recommended for best results (use a clean, lint-free cloth). Ensure surface is dry and residue free before proceeding.
Note: The position of the adhesive support base cannot be changed after it has been affixed.
1. With the protective backing still intact, place the adhesive support base on the back or the side of the terrarium to determine its final position and mark the position with a wax pencil or other marker.
2. Remove the protective backing and carefully fit the adhesive support base within the marked area.
3. Press the adhesive tape firmly and evenly against the glass panel, while gently twisting, to ensure proper adhesion. Make sure no air bubbles are showing. Once in place, the adhesive support base should not be removed!
4. Let the Reptile Dome NANO rest on the terrarium mesh for 24 hours to allow the tape bond to cure properly before the dome is suspended and the weight of the dome can exert pressure on the adhesive support base. Allow the adhesive tape bond to cure for 24 hours! INSTALL LIGHT AFTER 24 HOURS TO ALLOW THE TAPE BOND TO CURE PROPERLY
5. Adjust the height and tighten the screw of adhesive supporting base when the Exo Terra Reptile Dome NANO is suspended above the terrarium at the desired height.
6. Ensure that the light’s focal point is not positioned above any plastic parts of the terrarium or screen cover to prevent damage.
7. Screw light bulb into the Exo Terra Reptile Dome NANO (follow maximum wattage guidelines: 40W Max.). TIP: apply a thin layer of petroleum jelly to the threads on the base of the light bulb before screwing it in. This will make it easier to unscrew the bulb when it is time to replace it.
COMBINE WITH
Ideal for use with Exo Terra’s Daylight Basking Spot NANO, Daylight LED Spot NANO or Infrared Basking Spot NANO.
Combine multiple fixtures to create a 24-hour cycle and/or to provide UV light to animals with UV-requirements.
Combine the Reptile Dome NANO Fixture with an Exo Terra Compact Top holding a Reptile UVB100, Reptile UVB150 or Reptile UVB200 depending on your animal’s UV requirements.